Select Page

CCEC QSK50-C1600 Industrial Engine

CCEC QSK50-C1600 (1800 RPM) Industrial Engine is V type 16-cylinder, 50.3 liters four-strokes engine with 159 mm (6.25 in) bore and 159 mm (6.25 in) stroke.

QSK50-C1600 Industrial Engine equipped with CCECModular Common Rail Fuel System, comes with turbocharger and Water-Air intercooler, with a EURO II post-processor. The Advertised power at 1800 RPM of CCEC QSK50-C1600 Industrial Engine is 1600 HP (1193 kW). The maximum torque of the engine at 1500 RPM is 6835 N.m.

As part of EMAC, ConeMac provides industrial power pack solution that integrated with air intake, air exhaust, cooling system, control system, transmission and hydraulic accessories, We also supplying special products such as explosion proof engine, generator and water pump set, as well as ultra-low temperature condition engine power pack.

We provide full life cycle services for all customers, from design to power system supply, from installation to commissioning, from after-sales service training to spare parts supply, from trouble shooting to overhaul technical support.

Advantages of CCEC QSK50-C1600 Industrial Engine

  • Lower oil consumption, Extended stroke, the expansion of the combustion gas more fully, Increase effective efficiency output, the economy is better.

  • Strong power, advanced 4 air valves structure, greater horsepower, air burning more thoroughly, while making low speed torque increase, quicken response speedily, climb strongly.

  • Excellent reliability, with compulsive cold cut articulated pistons, Can bear extreme high mechanical load and heat load, Strength can be comparable with heavy engine.

  • Better emissions, Decorate injector and symmetrical combustion chamber in center, make the cylinder is more homogeneous mixture, burning more fully, lower emissions.

  • Super life, 30 % engines 800,000 km without overhaul.

  • Excellence power, Clean burning, use the advanced lean-burn closed loop electronic control system.

  • Excellent cold start performance, equipped with air suction electric preheater and 7.8 kW power starter, completely improve the cold start performance of the engine. Through the arctic village-MoHe of China -36 °C extreme low temperature validation.

Technical Specifications

Basic Introduction of CCEC QSK50-C1600 Industrial Engine

Engine Model:QSK50-C1600
Engine Type:V-16 Cylinder 4-Stroke 4-Valve
Displacement:50.3 L
Rated Speed:1800 RPM
Rated Power / Speed:1600 HP @ 1800 RPM
Aspiration Method:Turbocharged & Water-Air Intercooler
Emission Standard:U.S. EPA Tier 2
Bore * Stroke:159 mm * 159 mm
Packing Size (L * W * H):2857 mm * 1415 mm * 1766 mm
Wet Weight:6373 kg
Lead Time:15-30 Working Days
Payment Terms:T/T ,L/C

Coming Soon

Coming Soon

coming soon

Engine Model

Advertised power

Peak Torque

Curve & Datasheet

Compression Ratio

Fuel System

QSK50-C14001400 HP @ 1800 RPM4705 lb-ft (6379 N-m) @ 1300 RPMFR 679515.0 : 1Cummins MCRS
QSK50-C15001500 HP @ 1800 RPM4846 lb-ft (6570 N-m) @ 1400 RPMFR 679015.0 : 1Cummins MCRS
QSK50-C16001600 HP @ 1800 RPM5041 lb-ft (6835 N-m) @ 1500 RPMFR 678215.0 : 1Cummins MCRS
QSK50-C16751675 HP @ 1800 RPM5455 lb-ft (7396 N-m) @ 1500 RPMFR 679415.0 : 1Cummins MCRS
QSK50-C25002500 HP @ 1900 RPM7081 lb-ft (9601 N-m) @ 1500 RPMFR 689015.0 : 1Cummins MCRS
——END——

General Infomation of CCEC QSK50-C1600 Industrial Engine

Engine ModelQSK50-C1600Emission StandardU.S. EPA Tier 2
Advertised Power1,600 HP (1,193 kW) @ 1,800 RPMPeak Torque 5,041 lb-ft (6,835 N-m) @ 1,500 RPM
Curve & DatAsheetFR 6782Governed Power1,600 HP (1,193 kW) @ 1,800 RPM
Compression Ratio15.0 : 1Packing Size (L * W * H)2857 mm * 1415 mm * 1766 mm
TypeV 16 Cylinder, 4 Stroke , 4 ValveDisplacement3,067 in³ ( 50.3 L )
Fuel SystemCummins MCRSBore * Stroke6.26  in * 6.26 in / 159 mm * 159 mm
AspirationTurbocharged & Water-Air IntercoolerMinimum Low Idle Speed600 RPM
ConfigurationD283038CX03Maximum Low Idle Speed1,400 RPM
CPL Code3548Minimum speed for full load sustained operation1,700 RPM

Engine Sound Pressure Levels3 (Noise) Data of CCEC QSK50-C1600 Industrial Engine

Top Side106.1 dBaRight Side103.5 dBa
Left Side104.6 dBaFront Side101.4 dBa
Exhaust126.6 dBa

General Engine Data of CCEC QSK50-C1600 Industrial Engine

Maximum overspeed capability2,250 RPMMaximum installed engine power angle6 °
Mass moment of inertia of rotating components (excluding flywheel)N / AMaximum installed engine tilt angle6 °
Engine weight (mining market)⁴ Approximate Dry Weight13,162 lb / 5,970 kgEngine weight (mining market)⁴ Approximate Wet Weight14,050 lb / 6,373 kg
Engine weight (locomotive market)⁴ Approximate Dry Weight14,021 lb / 6,360 kgEngine weight (locomotive market)⁴ Approximate Wet WeightTBD lb / TBD kg
Engine weight (oil and gas market)– Approximate Dry Weight13,162 lb / 5,970 kgEngine weight (oil and gas market)– Approximate Wet Weight14,050 lb / 6,373 kg

Engine Mounting Data of CCEC QSK50-C1600 Pump Engine

Moment of Inertia — X Axis (Roll)5346 in lbf sec² / 604 kg m2Moment of Inertia — Y Axis (Pitch)24,711 in lbf sec² / 2,792 kg m2
Moment of Inertia — Z Axis (Yaw)23,879 in lbf sec² /  2,698 kg m2Center of Gravity — From Rear Face of Block40.59 in / 1,031 mm
Maximum Crankshaft Thrust Bearing Load Limit — Intermittent Load2,001 lbf / 8,900 NMaximum Crankshaft Thrust Bearing Load Limit — Continuous Load1,000 lbf / 4,450 N
Maximum Static Bending Moment at  Rear Face of Block4499 lb ft / 6100 N.mMaximum Bending Moment Available From Front of Crankshaft — 90 Degrees2,611 lb ft / 3,540 N.m
Center of Gravity — From Engine Centerline to Left Side of Engine (as Viewed From Rear of Engine)N / AMaximum Bending Moment Available From Front of Crankshaft — 180 Degrees5,156 lb ft / 6,991 N.m
Maximum Bending Moment Available From Front of Crankshaft — 0 Degrees1,887 lb ft / 2,559 N.mMaximum Bending Moment Available From Front of Crankshaft — 270 Degrees4,139 lb ft / 5,612 N.m
Center of Gravity — Above Crankshaft Centerline7.87 in /  200 mm
——END——

Performance Data of CCEC QSK50-C1600 Industrial Engine

Advertised PowerPeak TorqueAdvertised PowerPeak Torque
Engine Speed1,800 RPM1,500 RPMInlet Air Flow4,042 ft3/min1,908 L/s3,251 ft3/min1,534 L/s
Power Output1,600 HP1,193 kW1,440 HP1,074 kWExhaust Gas Flow8,678 ft3/min4,096 L/s7,910 ft3/min3,733 L/s
Torque Output4,669 lb ft6,330 N.m5,041 lb ft6,835 N.mExhaust Gas Temperature739 °F393 ℃862 °F461 ℃
Friction Horsepower221 HP165 kW160 HP119 kWHeat Rejection to Ambien Air5,036 BTU/min89 kW4,611 BTU/min81 kW
Intake Manifold Pressure62 in Hg208 kPa56 in Hg189 kPaHeat Rejection to Exhaust Gas53,804 BTU/min946 kW51,864 BTU/min912 kW
Turbo Comp. Outlet Pressure63 in Hg212 kPa56 in Hg190 kPaHeat Rejection to LTC Coolant16,348 BTU/min287 kW12,343 BTU/min217 kW
Turbo Comp. Outlet Temperature354 °F179 ℃336 °F169 ℃Heat Rejection to HTC Coolant24,781 BTU/min436 kW23,776 BTU/min418 kW
——END——

System Technical Data of CCEC QSK50-C1600 Industrial Engine

Intake Air SystemMaximum Air Temperature Rise Over Ambient at  Turbocharger Compressor Inlet20 delta °F / 11.1 delta °C
Maximum Intake Air Restriction With Clean Filter12 in H2O /  3.0 kPa
Maximum Intake Air Restriction With Dirty Filter25 in H2O /  6.2 kPa
Minimum Air Cleaner Dirt Holding Capacity25 g / cfm
Maximum Intake Air Bleed for Accessories at  Intake Manifold (Not Including Air Compressor)N / A
Recommended Intake Piping Size (Inner Diameter)6.0 in / 152 mm
Exhaust SystemMaximum Exhaust Restriction3 in Hg / 10 kPa
Recommended Exhaust Piping Size (Inner Diameter)7.79 in / 198 mm
Maximum Static Bending Moment at  Exhaust Outlet Flange16 lb ft / 21.0 N.m
Lubrication SystemNominal Operating Oil Pressure at  Minimum Low Idle Speed29 PSI / 200 kPa
Nominal Operating Oil Pressure at  Advertised Speed83 PSI / 570 kPa
Minimum Oil Pressure Within 4 Seconds of Engine First Firing at  Minimum Low Idle Speed (MeAsured at  Urbocharger Oil Inlet)20 PSI / 138 kPa
Maximum Oil Flow to All Accessories12 gpm / 45.42494 L/min
Maximum Oil Pressure Spike on Cold Engine240 PSI / 1,655 kPa
Fuel SystemMaximum Heat Rejection to Return Fuel Which Occurs at  The Following Conditions133 BTU/min / 2 kW
Maximum Heat Rejection to Return Fuel Which Occurs at  The Following Conditions Fuel Return Flow536 lb/hr / 243 kg/hr
Maximum Heat Rejection to Return Fuel Which Occurs at  The Following Conditions Fuel Return Temperature (Prior to Fuel Cooler)150 °F / 66 °C
Maximum Fuel Supply Flow1086 lb/hr / 493 kg/hr
Maximum Fuel Return Flow536 lb/hr / 243 kg/hr
Maximum Fuel Supply Temperature (MeAsured at  On-Engine Fuel Inlet Fitting)158 °F / 70 °C
Maximum Fuel Supply Pressure (MeAsured at  On-Engine Fuel Inlet Fitting)5 PSI / 34 kPa
Maximum Fuel Return Restriction (MeAsured at  On-Engine Fuel Drain Fitting)10 in Hg /  34 kPa
Fuel System Stage 1 filter(s)Maximum Combined Fuel Supply Restriction of Stage 1 Assembly & Oem Plumbing (MeAsured at  On-Engine Fuel Inlet Fitting) With Clean Stage 1 Fuel Filter(S) at  Maximum Fuel Supply Flow5 in Hg /  16.9 kPa
Maximum Combined Fuel Supply Restriction of Stage 1 Assembly & Oem Plumbing (MeAsured at  On-Engine Fuel Inlet Fitting) With Dirty Stage 1 Fuel Filter(S) at  Maximum Fuel Supply Flow10 in Hg /  33.8 kPa
Nominal Restriction of Clean Stage 1 Fuel Filter Assembly at  Maximum Fuel Supply Flow2 in Hg /  7 kPa
Maximum Fuel Inlet Pressure MeAsured at  Stage 1 Inlet3 PSI / 21 kPa
Recommended Maximum Fuel Inlet Pressure For Seeing Is Believing® (MeAsured at  Stage 1 Inlet)2 PSI / 14 kPa
Fuel System Stage 2 filter(s)
Maximum fuel supply restriction from low pressure fuel pump outlet to Stage 2 filter head inlet10 in-Hg / 34.0 kPa
Maximum fuel supply restriction from Stage 2 filter head outlet to high pressure fuel pump inlet10 in-Hg / 34.0 kPa
Cooling SystemsCooling System Type2 Pump 2 Loop
Cooling Systems Requirements of both LTC and HTC cooling circuitsMinimum Fill Rate5 gpm / 19 L/min
Maximum Deaeration Time25 min
Acceptable Types of Deaeration SystemsFully Deaerating
Minimum Water Pump Inlet Pressure With Fully Deaerating Cooling SystemN / A
Maximum Static Head of Coolant Above Crankshaft Centerline 60 ft / 18.3 m
Minimum Pressure Cap Rating at  Sea Level11 PSI / 76 kPa
Maximum Pressure Cap Rating at  Sea Level15 PSI / 103 kPa
Minimum Coolant Expansion Space (% of Total Cooling System Capacity)6 %
Minimum Drawdown (% of Total Cooling System Capacity)11 %
Cooling Systems Low Temperature (Aftercooling) Circuit (LTC)LTC coolant volume (engine only)32 quarts / 30 L
LTC thermostat opening temperature115 °F / 46 °C
LTC thermostat fully open temperature135 °F / 57 °C
Maximum LTC aftercooler inlet temperature at 77 °F (25 °C) ambient air temperature120 °F / 49 °C
Maximum LTC aftercooler inlet temperature at LAT165 °F / 74 °C
Maximum external LTC restriction at 1800 RPM12 PSI / 83 kPa
Cooling Systems High Temperature Circuit (HTC)HTC Coolant Volume (Engine Only)148 quarts / 140 L
HTC Thermostat Opening Temperature180 °F / 82 °C
HTC Thermostat Fully Open Temperature202 °F / 94 °C
Maximum HTC Thermostat Outlet Temperature at Lat (Maximum Top Tank Temperature)212 °F / 100 °C
Minimum Operating HTC Temperature (for Continuous Cold Weather Applications)160 °F / 71 °C
Maximum External HTC Restriction at 1800 Rpm12 PSI / 82.7 kPa
Maximum Auxiliary Coolant FlowN / A
Electrical SystemSystem Voltage24 V
Minimum Battery Capacity for Engine Only [Cold Soak at 0 °F (-18 °C) Or Above] Cold Cranking Amperes (Cca)1800 CCA
Minimum Battery Capacity for Engine Only [Cold Soak at 0 °F (-18 °C) Or Above] Reserve Capacity (Rc)640 min
Cranking SystemMinimum Cranking Speed150 RPM
Maximum Parasitic Load 10 °F (-12 °C)N / A
Unaided Cold Start Minimum Ambient Temperature10 °F /  12 °C
Unaided Cold Start Cranking Torque at Minimum Unaided Cold Start TemperatureN / A
Aided Cold Start Minimum Ambient Temperature with Only Ether– 26 °F / 32 °C
Aided Cold Start -Minimum Ambient Temperature with Only Coolant And Oil Heaters– 26 °F / 32 °C
——END——

 

Scopes of Supply of CCEC QSK50-C1600 Industrial Engine

Fuel System1. Fuel Transfer PumpExhuast System1. Exhuast Manifold
2. High-Pressure Fuel Pump2. Turbocharger
3. Fuel Filter3. Exhuast Elbow
Air Intake System1. Air Intake ManifoldStarting System1. Starter Motor
2. N/A2. Starter Rely
Cooling System1. Water PumpPower Output System1. Flywheel
2. Engine Fan2. Standard Flywheel Housing
3. Standard Radiator3. N/A
Lubricating System1. Oil PumpCharging System1. Charging Alternator
2. Oil Filter2. N/A
Engine Shut-Down System1. Engine Fuel Shut-Off SolenoidrEngine Mounting System1. Engine Mouting Bracket
Engine Auiliary Accessories1. Air Compressor
——END——

Optional Accessories of CCEC QSK50-C1600 Industrial Engine

Air Intake System1. Air Intake Pre-HeaterExhuast System1. Muffler & Bellows
2. Air Intake Shut-Off Valve2. Flame Trap
3. Air Filter3. Spark Arrestor Type Muffler & Bellows
4. Air Intake Pre-Filter4. Dpf System
5. Air Filter Alarm System5. N/A
Fuel System1. Coarse FilterLubricating System1. Oil Pre-Heater.
2. Fuel Pre-Heater2. N/A
Starting System1. Manual Magnetic Dc ContactorCooling System1. Silent Type Radiator
2. Dual Ears Flywheel Housing2. Plateau Radiator
3. Spring Starter Motor3. Salt-Spray Resistant Radiator
4. Air Starter Motor4. Coolant Pre-Heater
5. Hydraulic Starter Motor5. Jacket Water Heater
6. Manual Magnetic Dc Contactor6. N/A
Engine Auiliary Accessories1. Hydraulic Oil PumpControl System1. Can Add Engine Monitoring System, Contro System With Wiring Harness.
2. Air Conditioner Compressor2. Can Add Self-Protection System that Integrated with Alarm System.
Power Output System1. ClutchEngine Mounting System1. Shock Absorber Pad
——END——

Committed to Providing Stable and Reliable Premiem Power System for Global Construction Machinery Manufacturer Partners, ConeMac is A Sub-Brand of the EMAC Group that Focuses on Construction Equipment Application.
ConeMac’s Ranges of Products Mainly Inclduing Marine Construction Engines Power Pack, Construction Equipment Gearbox, Gear Reducer, Explosion-Proof Engines, Generator Set and Water Pump Set for Mining, Oil and Gas Field.
For More Information of Our Industrial Power System Products, You Are Welcome to Visit ConeMac Homepage: Conemac.cn

 

Modifiable Components of CCEC QSK50-C1600 Industrial Engine

Air Intake System1. Installation Position of Air FilterCharging System1. 12 V Charging Alternator for 12 v Electric System
2. Upgrade to Heavy-Duty Type Air Fitler2. Explosion-Proof Charging Alternator
3. N/A3. Upgrading to Specified Brand and Speicifications of Charging Alternator
Exhuast System1. Water-Cooled Exhuast ManifoldLubricating System1. Oil Pan Position
2. Water-Cooled Turbocharger2. Number of Dipstick
3. Can Modify Installation Position and Direction of Turbocharger3. Position of Dipstick Can Choose from 6 Positions
4. N/A4. Can Modify Oil Filter to be Remote Installation
Engine Shut-Down System1. 12 V Solenoid for 12 V Electric SystemStarting System1. Upgrading to Specified Brand and Speicifications of Starter Motor
2. Explosion-Proof Solenoid2. 12 V Starter Motor for 12 V Electric System
Fuel System1. Upgrade to Fuel Fitler that Integrated with Fuel Transfer Pump and Fuel Pre-HearterEngine Auiliary Accessories1. All of auxiliary System can Choose Specified Brands and Specifications
2. N/A2. Additional Auxiliary Systems Can be Added for Special Applications
Cooling System1. Can Modify Engine fan Into Blower Fan or Suction FanPower Output System1. Can Modify Size of Flywheel Housing and Flywheel
2. Can Modify Central Position of Engine Cooling Fan2. Dual-Ear Flywheel Housing (For Twin-Starter System)
3. Can Choose Type of Engine Fan From Mechanical Type or Electric Type3. Some of Models can Modify Flywheel Housing Into PTO Integrated Type
4. N/A4. Engine Have Connecting Port of PTOs, That Able to Provide Power Output
Engine Mounting System1. Can Modify Engine Mouting Bracket
——END——

Note: All Above Data are Just for Reference, All Data Might Change Without Notices or Updates, Please Contact Our Sales Team to Confirm All Details Via WhatsApp or Email.

WhatsApp-Online-logo

Sales Team


Marine Service - SeaMacWhatApp-Icon

Automotive Service - DuraMacWhatApp-Icon

Industrial Service - ConeMacWhatApp-Icon

Generator Service - SinoGenWhatApp-Icon

Pump Service - PumpMacWhatApp-Icon

Parts Service - PartMacWhatApp-Icon

Sales Manager - Mrs. Wendy Fu

Sales Director - Mr. Jasper Lee       WhatApp-Icon


Shipping Service

Contact EMAC Now!

Subscribe To Our Newsletter

Subscribe To Our Newsletter

Subscribe to get the latest updates from www.ccec-engine.com

You have Successfully Subscribed!

Pin It on Pinterest