Select Page

Precautions During CCEC Engine Operation

Nov 26, 2021 | Operation and Maintenance | 0 comments

The problems that should be paid attention to during the operation of CCEC engine. If the daily operation of the CCEC engine is not standardized, it will affect the service life and work efficiency of CCEC. Therefore, during the operation of the CCEC engine, the correct operation must be standardized.

Precautions During CCEC Engine Operation

  1. Requirements for Normal Engine Start
  • CCEC starter does not exceed 30s each time, and the time interval between restarts is 2min.
  • The lubricating oil pressure should reach 70KPa within 15s after starting, otherwise check the oil level immediately.
  • After starting, the load can be applied at idling speed for 3-5 minutes, otherwise the bearing bush will be short of oil supply in an instant.
  • Idle speed should not exceed 10 minutes, otherwise undesirable phenomena such as carbon deposits in the combustion chamber and oil leakage from the CCEC engine turbocharger will occur.
  • The water temperature of the CCEC engine should not be lower than 60℃, otherwise the fuel will enter the oil and destroy the lubrication. The water temperature can be increased by accelerating with an empty car.
  • After starting in winter, keep idling until the pointer of the water temperature gauge rotates or enter operation after 10 minutes. While observing the water temperature gauge, pay attention to whether the oil pressure gauge meets the requirements. When using auxiliary starting fluid in winter, be sure to use a sprayer with a metering hole.

Precautions During CCEC Engine Operation

  1. Basic Engine Operating Requirements
  • Always observe the instrument during CCEC engine operation: the water temperature should be between 74°C and 91°C; the oil pressure should be greater than 70KPa at idling speed, and should be within the range of 276-517kPa when it is above 1200r/min.
  • If the CCEC engine is overheated, run it at a reduced load. If it is overheated after running for a period of time under reduced load, the machine should be shut down to check the fault.
  • During CCEC engine operation, you should pay close attention to the changes in the following conditions of the engine. If any one of them changes suddenly, it is likely to be a sign of failure. Please check and repair it in time.

1Engine extinguishes or catches fire badly;

2Vibration;

3The engine has abnormal noise;

4Sudden changes in generator working pressure and temperature;

5Engine exhaust smoke is too large;

6Insufficient engine power;

7Increased oil consumption;

8Increased fuel consumption;

9Fuel, oil or water leaks.

Precautions During CCEC Engine Operation

  1. Engine Operating Range
  • When the CCEC engine is lower than the maximum torque speed, the full throttle operation should not exceed 30s, otherwise the overhaul life of the engine will be shortened and the engine may be seriously damaged. CCEC diesel generator sets work best above the maximum torque speed point, so it is recommended to run CCEC engine within this range.

Note: EMAC recommends that you do not run the CCEC engine above the maximum idle speed under any circumstances or environment.

Precautions During CCEC Engine Operation

  1. CCEC Engine Operating in a Cold Environment
  • As CCEC agent EMAC, we recommend that you use special oil, fuel and coolant when running the engine in extremely cold environments.

Precautions During CCEC Engine Operation

  1. Engine Shutdown
  • The CCEC engine is required to idle for 3-5 minutes before stopping. Because the diesel engine idling for 3-5 minutes before stopping each time, the oil can take away the heat in the combustion chamber, bearings and oil seals, especially the supercharger. According to EMAC’s many years of experience, if a sudden shutdown occurs, the bearing and oil seal are likely to be seized.
  • The purpose of CCEC engine shutdown can be achieved by cutting off the current of the fuel pump solenoid valve.

Note: If you want to know more about CCEC engine information, please visit our website https://www.dcec-engine.com/

0 Comments

Submit a Comment

Your email address will not be published.

WhatsApp Online logo

Sales Team


Marine Sales - Mrs. Gazit Wong WhatApp-Icon

Train Sales - Mrs. Gazit Wong WhatApp-Icon

Automotive Sales - Mrs. Shelly LiuWhatApp-Icon

Industrial Sales - Mrs. Kitty Chen WhatApp-Icon

Generator Sales - Mrs. Erica WhatApp-Icon

Pump Sales - Mrs. Ryen WhatApp-Icon

Spare Parts - Mrs. Nora Chen WhatApp-Icon

Sales Manager - Mrs. Wendy Fu

Ventas españolas - Victoria

Sales Director - Mr. Jasper Lee       WhatApp-Icon

Contact EMAC Now!

Subscribe To Our Newsletter

Subscribe To Our Newsletter

Subscribe to get the latest updates from www.ccec-engine.com

You have Successfully Subscribed!

Pin It on Pinterest